 |
|
|
|
|
|
|
| |
Home >
Austaron >
Staron Bathroom Surfaces
STARON BATHROOM SURFACES
Install, Maintain :
Index |
|
Care & Maintenace
Staron is a homogeneous and solid mineral-filled acrylic polymer material that is easy to maintain.
Simple routine maintenance is required to keep it looking new and fresh.
Routine Cleaning of Countertops and Sinks
Use soap and water with soap or an ammonia-based cleanser (such as glass cleanser).
Wipe away water stains with a damp cloth and sponge and dry with a towell.
Removing Difficult Stains:
Dull Finishes: Use an abrasive cleanser and a green Scotch-Brite(r) pad. Rub in a circular motion.
Semi-Gloss Surfaces: Use Soft Scrub(r) diluted bleach and a white Scotch-Brite(r) pad.
Rub in a circular motion.
High-Gloss Surfaces: Follow the procedure for semi-gloss surfaces, but use a sponge instead of a Scotch-Brite(r) pad. If the area is dull in contrast with the surrounding surface, use a white polishing compound with a sponge to get a higher gloss.
Disinfecting Surfaces and Sinks
Occasionally wipe sinks and bowls with diluted household bleach (1/1 water/bleach solution) to disinfect.
Removing Cuts and Scratches
Dull finishes: Sand with 180-grit (120 micron) or 220-grit (60 micron) fine sandpaper until the cut and scratch is removed; restore finish with an abrasive cleanser and a green Scotch-Brite(r) pad to the same finish as the adjacent surface.
Semi-Gloss Finishes: Sand with 400-grit (30 micron) sandpaper; restore finish with a nonabrasive cleanser and a white Scotch-Brite(r) pad.
High-gloss finishes: Sand with 400-grit (30 micron) or 600-grit (20 micron) sandpaper; buff with polishing pad at a low speed (1500 - 2000 rpm) polisher equipped with a wool pad; finish with a wax.
All of the above sanding and polishing should be done in a circular motion.
Preventing damage
In most cases, Staron can be easily repaired. However, follow these guidelines to prevent any permanent damage.
Heat damage
Even though Staron has an excellent heat resistant property compared
with other ordinary countertops, placing hot pans, as well as some
heat-generating appliances such as frying pans or crockpots can
damage a Staron surface. Always use a hot pad or a trivet with rubber
feet to protect Staron. Avoid long-term exposure of Staron to temperatures over 80°C
(170°F).
Other Damage
Avoid exposing Staron to strong chemicals such as paint removers and
oven cleaners. Surfaces exposed to these chemicals should be
promptly flushed with water. Contact over a long period of time will
cause spots and require extensive sanding.
* Do not cut directly on a Staron surface.
* Use a cutting board.
* Run cold water when pouring boiling water into sinks.
* Remove nail polish with a non-acetone-based nail polish remover and flush with water.
All the above sanding and polishing should be done in a circular motion
RESIDENTIAL 10-YEAR LIMITED WARRANTY
BY SAMSUNG/CHEIL INDUSRTRIES INC.
Permanently installed STARON surfaces of the original owner is warranted by SAMSUNG/CHEIL INDUSTRIES INC. (hereunder 'SAMSUNG') in the United States and Canada. STARON must be fabricated, installed, used and maintained in accordance with instructions provided by SAMSUNG. SAMSUNG at its option will repair or replace, without charge, such products if it falls due to any manufacturing defect during the first ten (10) years after the date of initial installation except for damage caused by physical or chemical abuse, damage from excessive heat, or act of nature. This includes necessary real cost charges needed to repair or replace the products. All of instructions are available from your dealer and fabrication/installation source or by contacting SAMSUNG.
This warranty is transferable within 10-year period since the first installation only when the new owner writes to SAMSUNG to register the installation under a new owner's name.
This Warranty does not cover:
- Minor conditions such as stains, scratches, water spots and burns which, due to the unique properties of STARON, may be corrected by techniques specified in Care & Maintenance instructions
- Failure not to comply with SAMSUNG's instructions including fabrication, installation, care, maintenance, etc.
- Any products moved from their original place of installation.
- Failure or dissatisfaction with appearance of joints or seams, or of any adhesive, caulk or other accessory items.
|
All products contained herein © Austaron. Page layout © 1996-2009 Architecture Media (Selector) Pty Ltd.
All rights reserved.
|
|
|
|
Photographs